LCD Keypad shield 16x2 - являє собою плату розширення arduino з дворядковим екраном по 16 символів у кожному рядку та 6 кнопками управління. Його дуже зручно використовувати в Ардуїно проектах, так як підключити шилд до Ардуїно займає лічені секунди.
Розробники LCD Shield підключили всі шість кнопок послідовно через резистори з різним опором до аналогового входу ардуїно. Що дозволило заощадити 5 цифрових пін ардуїно.
Характеристики LCD Shield:
LCD shield сумісний з Arduino Mega та Arduino Uno
Є підстроювальний резистор для регулювання контрасту зображення.
Кнопки керування: LEFT, RIGHT, UP, DOWN, SELECT, RESET
Кнопки: Select, Up, Right, Down, Left, підключені на пін A0 ардуїно
Використання висновків ардуїно для підключення дисплея: D4 - D10
Напруга живлення: 4.5В.. 5.5В
Струм споживання: 2 мА (без підсвічування)
Підсвічування синє.
Інтерфейс: 28 контактів у два ряди (16+12)
Розмір символу: 2.95 × 4.35 (w × h) мм
Розмір: 80 x 60 мм
Вага: 53 г
Скетч для Arduino LCD Shield для тестування LCD-екрана та кнопок модуля
//У прикладі використовується бібліотека LiquidCrystal
#include
// Select the pins used on the LCD panel
LiquidCrystal lcd(8, 9, 4, 5, 6, 7);
// define some values used by the panel and buttons
int lcd_key = 0;
int adc_key_in = 0;
#define btnRIGHT 0
#define btnUP 1
#define btnDOWN 2
#define btnLEFT 3
#define btnSELECT 4
#define btnNONE 5
// read the buttons
int read_LCD_buttons()
{
adc_key_in = analogRead(0); // read the value from the sensor
// My buttons when read are centered at thes valies: 0, 144, 329, 504, 741
// we add approx 50 до тих пір, як ціни і check to see if we are close
if (adc_key_in > 1000) return btnNONE; // We make this the 1st option for speed reasons since it will be the most likely result
// For V1.1 us this threshold
if (adc_key_in < 50) return btnRIGHT;
if (adc_key_in < 250) return btnUP;
if (adc_key_in < 450) return btnDOWN;
if (adc_key_in < 650) return btnLEFT;
if (adc_key_in < 850) return btnSELECT;
// Для V1.0 повідомити про іншу threshold and use the one below:
/*
if (adc_key_in < 50) return btnRIGHT;
if (adc_key_in < 195) return btnUP;
if (adc_key_in < 380) return btnDOWN;
if (adc_key_in < 555) return btnLEFT;
if (adc_key_in < 790) return btnSELECT;
*/
return btnNONE; // when all others fail, return this...
}
void setup()
{
lcd.begin(16, 2); // start the library
lcd.setCursor(0,0);
lcd.print("Push the buttons"); // Print a simple message
}
void loop()
{
lcd.setCursor(9,1); // move cursor to second line "1" і 9 spaces over
lcd.print(millis()/1000); // display seconds elapsed since power-up
lcd.setCursor(0,1); // move to the begining of the second line
lcd_key = read_LCD_buttons(); // read the buttons
switch (lcd_key) // depending on which button був pushed, we perform an action
{
case btnRIGHT:
{
lcd.print("RIGHT");
break;
}
case btnLEFT:
{
lcd.print("LEFT");
break;
}
case btnUP:
{
lcd.print("UP");
break;
}
case btnDOWN:
{
lcd.print("DOWN");
break;
}
case btnSELECT:
{
lcd.print("SELECT");
break;
}
case btnNONE:
{
lcd.print("NONE");
break;
}
}
}